Description

MATEK F405-WTE – Mateksys FLIGHT CONTROLLER SPECIFICATIONS

Use: Vehicles & Remote Control Toys

Recommend Age: 12+y,14+y

Origin: Mainland China

Material: Composite Material

Brand Name: MATEKSYS

FLIGHT CONTROLLER F405-WTE

STM32F405RGT6, ICM42688P, SPL06, OSD, ESP WIFI telemetry/ELRS 2.4G receiver, 6xUARTs, 12x PWM,1xI2C

MATEKSYS Flight Controller F4O5-WTE MCU STM3ZFAOSRGT6 IMU ICM42688-P Barometer SPLO6-001 OSD AT7456E BlackBox MicroSD 2 8 2 2 2 ESP WiFi Telemetry(MAVLink) 2 or ExpressLRS 2.4G receiver(CRSF protocol) 6x UARTs , Ix I2C , 4x ADC 85 12x PWM outputs Switchable dual camera inputs 4+

FC Specifications

• MCU: STM32F405RGT6, 168MHz , 1MB Flash

• IMU: ICM42688-P

• Baro: SPL06-001

• OSD: AT7456E

• Blackbox: MicroSD card slot

• ESP WiFi Telemetry(MAVLink, 14dBm)

• ExpressLRS 2.4G receiver(CRSF protocol, Telemetry 12dBm)

• 6x UARTs, 1x Softserial_Tx option(INAV)

• 12x PWM outputs

• 1x I2C

• 4x ADC (VBAT, Current, RSSI, Airspeed)

• USB/Beep Extender with Type-C(USB2.0)

• Dual Camera Inputs switch

• 9V(12V) for VTX power switch

FC Firmware

• ArduPilot: MatekF405-TE

• INAV: MATEKF405TE_SD (not available in INAV configurator 4.x)

PDB

• Input voltage range: 6.8~30V (2~6S LiPo)

• 1x ESC power pads

• Battery Voltage divider 1K:20K (Scale 2100 in INAV, BATT_VOLT_MULT 21.0 in ArduPilot)

• Current Senor: 220A, 3.3V ADC (Scale 150 in INAV, 66.7 A/V in ArduPilot)

• Sense resistor: 90A continuous, 220A peak

BEC 5V output

• Designed for Flight controller, Receiver, OSD, Camera, Buzzer, 2812 LED_Strip, Buzzer, GPS module, AirSpeed

• Continuous current: 2Amps, Max.3A

BEC 9V /12V output

• Designed for Video Transmitter, Camera, Gimbal ect.

• Continuous current: 2Amps, Max.3A

• 12V option with Jumper pad

• for stable 9V/12V output, input voltage should > output voltage +1V

BEC Vxoutput

• Designed forServos

• Voltage adjustable, 5V Default, 6V or 7.2V via jumper

• Continuous current: 8Amps, Max.10A

• for stable Vx output, input voltage should > Vx voltage +1V

BEC 3.3Voutput

• Designed for Baro / Compass module and external 3.3V peripherals

• Linear Regulator

• Continuous current: 200mA

Physical

• Mounting: 25 x 25mm, 2mm

• Dimensions: 44 x 29 x 12.7mm

• Weight: 22g w/ USB/buzzer adapter

Including

• 1x F405-WTE

• 1x USB(Type-C)/Beep (Passive buzzer) Extender + 20cm JST-SH-6P to JST-SH-6P cable for USB extender.

• 2x IPEX-MHF1 2.4G Antennas

• 1x Rubycon ZLH 35V 470uF capacitor

• Dupont 2.54 pins(Board is shipped unsoldered)

ArduPilot ESP8266 wifi telemetry

• https://ardupilot.org/copter/docs/common-esp8266-telemetry.html

• Tool:ESP_NodeMCU-PyFlasher.exe

• Firmware:firmware-esp01_1m.bin

• Flashing with ESP_NodeMCU-PyFlasher

  1. Wire the ESP8285(ETx, ERx) into the USB-TTL adapter, with ETx on F405-WTE connected to the Rx on the USB-TTL, and ERx connected to the Tx of the USB-TTL. Wire 4v5 and GND of F405-WTE to 5V and GND of the USB-TTL

  2. Connect USB-TTL Adapter to PC while pressing and holding the ESP8285 boot button in.

  3. open ESP_NodeMCU-PyFlasher

  4. selectSerial portof USB-TTL module, load firmware, select Dual Output(DOUT) and Yes.wipes all data

  5. click Flash NodeMCU

  6. after flashing, Power off , then power on F405-WTE by USB or Battery.

  7. Wait a few seconds, search WiFi SSID ArduPilot, and password is ardupilot

  8. Tips: Red LED for ELRS receiver will not turn on if MAVESP8266 firmware is flashed in.

ExpressLRS 2.4G Receiver

• https://www.expresslrs.org/2.0/quick-start/getting-started/

• ExpressLRS AUX1-AUX8 are not full resolution CH.https://www.expresslrs.org/2.0/software/switch-config/

• Flashing via WiFi

  1. Power on F405-WTE by USB, Receivers LED(Red) will blink slow at first, and after 30s, it should blink fast indicating its on WiFi Hotspot Mode.

  2. More detailed steps, pls refer

     Reviews (0)

     Add a Review

     Your email address will not be published. Required fields are marked *

     Your review *

     Name *

     Email *